24 LB block MP Clear Glycerin Soap Base - Basic

Description

24 LB block MP Clear Glycerin Soap Base - Basic
Part Number:
1187
Feature 6
On low heat, warm base to 140º F or until it becomes liquid. Add cosmetic grade fragrance and FDA approved color additive. Pour into mold. Allow to return to room temperature and un-mold. Wrap in an air tight wrap. Label per FDA label requirements.
Note: Amount of fragrance cannot exceed IFRA guidelines (listed for each fragrance on this website) and should not exceed this product’s “Maximum Fragrance Load”. We do not recommend adding soap making oils & butters to mp soap as they will significantly decrease your lather. When using the soap, if the soap bubbles are not white then too much color has been used.
Feature 7
Directions Melt soap in double boiler or microwave oven. DO NOT let the soap boil. Add no more than 1 tablespoon of fragrance oil or 1 teaspoon of essential oil per pound of soap. Pour into mold and let rest until solid. Unmold and wrap immediately. Note Big block measures 13 x 11.5 x 6 inches. Picture displays a finished bar of soap. We do not recommend adding soapmaking oils & butters to mp soap as they will significantly decrease your lather.
Description
Country Of Origin:
United States
Our Crafter’s Choice Basic Clear Melt and Pour Soap Base has a beautiful, creamy lather. It is very clear and has a very low odor that does not compete with fragrance. Customers love the low water content because it means less and easy unmolding. This base is considered to be a low sweat in average weather conditions.
This soap is formulated with artificial additives which improve the soap’s ability to attract dirt, produce “big bubble” lather, and completely rinse off of the skin/tub. Further, these additives improve the soap’s ability to be artistically crafted.
Common Uses:
Cleansing agent. Bars of soap
Points of Interest:
Best base for those seeking an economical base with good performance. Soap base is a low sweat formula. Considered easy to unmold. No offensive chemical odors. 1 case = 24 lb. block of soap. Hypo-allergenic. Coconut Oil Base.
Country of Origin:
United States
Composition:
78% Naturally Derived Ingredients
Maximum Fragrance:
3% (Follow IFRA Guidelines)
Maximum Total Fluid Additives:
6%
Maximum Heating Temperature:
160º F
Recommended Container:
Air Tight Wrap
Physical Form:
Clear Solid
Solubility:
Soluble in water
Melt Point:
122º F.
Typical pH:
9.0-9.8 (this pH is required for dirt removal & rinsability)
This soap is formulated with artificial additives which improve the soap’s ability to attract dirt, produce “big bubble” lather, and completely rinse off of the skin/tub. Further, these additives improve the soap’s ability to be artistically crafted.
ingredients
-
Propylene Glycol, Sorbitol, Water, Sodium Stearate, Sodium Laureth Sulfate, Sodium Laurate, Glycerin, Triethanolamine.
Recommended Choice Aroma Additives:
Skin Safe Fragrance Oil - Maximum 3%
Skin Safe Essential Oil - Maximum 1%
Recommended Choice Color Additives:
Liquid Dye, Mica Powder, Mica Liquid
Storage:
Room temperature. Air tight container.
Best Used By:
One year from date of purchase.
Shelf Life Once Used in Manufacturing:
One year from manufacturing date.
Block of soap measures 13 x 11.5 x 6 inches.
MELT:
Determine amount of melt and pour soap base needed for your project. Carefully slice soap base into small pieces and place in microwave safe container. Heat on low at 30 second intervals. Stir between intervals until liquid. Handle hot soap carefully as it may burn the skin. Soap can also be melted in a double boiler.
MOLD:
Stir in cosmetic color, cosmetic scent, and skin safe additives. Pour into a mold. Spritz soap surface with rubbing alcohol to remove bubbles. Allow to cool until hard.
ENJOY:
Remove from mold and wrap with airtight plastic wrap. Your newly created melt and pour soap is now ready to use!
CAUTION:
Melted soap is hot!  For ages 15 and older.